The MTH T41 Series close-coupled and pedestal mounted regenerative turbine pumps represent the most economical, high performance alternative for low flow (1/2 to 22GPM) applications involving moderate to high pressures (heads to 600 feet). Handle entrapped gasses without vapor lock. Also known as jockey pump.
Steep Operating Characteristics
Near-constant deliveries are maintained over wide variations in load. High shut-off pressure overcomes temporary line resistance.
Near-constant deliveries are maintained over wide variations in load. High shut-off pressure overcomes temporary line resistance.
Standard Motor
Close-coupled T41 pumps use standard “C” face motors. Service and
replacement motors up to three horsepower are stock items in the U.S. and at
MTH.
Self-Adjusting Impeller
A hydrodynamic film on each side of the impeller positions it for long life.
The impeller exerts no thrust load on bearings. Pump operates equally well in
a vertical or horizontal position.
Mechanical Seals
Bronze fitted pumps have Buna N elastomers, high temperature carbon, and ceramic
seats for best hot water service. Optional seats and materials are also available.
300# Case Working Pressure
Rigid structure is designed for maximum casing strength.
100% Tested
Every pump is fully tested to verify performance prior to shipment.
Volatile Fluid Handling
Turbine impeller handles vapors up to 20% by volume, minimizing the possibility
of vapor locks.
”O”Ring Gaskets
“O”ring seals are used throughout the T41 series pumps to assure sealing
and ease of service.
Shaft Sleeve
Units up to three horsepower have a shaft sleeve under the mechanical seal.
Larger units have a 316 stainless steel shaft with an impeller sleeve.
Water Flinger
A water flinger provides added protection to ball bearings in the event of seal
leakage.
Simple Construction
T41 series pumps contain only three major components, allowing for easy service.
End Suction • Top Discharge
T41 Series pumps fit into small spaces easily. Discharge can be rotated in 90
degree, 180 degree and 270 degree positions.
Best Efficiency
New pump design optimizes efficiency for each size.
Non-Cavitating
T41 series pumps may be operated under adverse inlet conditions without audible
or measurable cavation.
Low NPSH
New inlet design provides superior fluid handling ability at low head inlet
conditions.burks aroura 43195K
For
Cross Reference to Aurora or Burks click here
 |
 |
 |
 |
 |
 |
 |
 |
||||||
Manufacturer: MTH Turbine Pump
Model Number: T41BAB053OB
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 1 HP
HP Standard : 0.5 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : Bronze
Elastomers : Buna-Nitrile
Voltage : 208-230/460 V
Phase : 3
Frequency : 50/60 Hz
Motor : ODP
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Flooded Suction
Applications : Boiler Feed
Applications : Chemical
Applications : Coolant
Applications : Cooling
Applications : Condensation
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications : Water Blast
PH High : 10 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$77050
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BAB051OB
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 1 HP
HP Standard : 0.5 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : Bronze
Elastomers : Buna-Nitrile
Voltage : 115/230 V
Phase : 1
Frequency : 50/60 Hz
Motor : ODP
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Flooded Suction
Applications : Boiler Feed
Applications : Chemical
Applications : Coolant
Applications : Cooling
Applications : Condensation
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications : Water Blast
PH High : 10 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$77050
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BAB753TB
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 0.75 HP
HP Standard : 0.75 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : Bronze
Elastomers : Buna-Nitrile
Voltage : 208-230/460 V
Phase : 3
Frequency : 50/60 Hz
Motor : TEFC
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Boiler Feed
Applications : Chemical
Applications : Condensation
Applications : Coolant
Applications : Cooling
Applications : Flooded Suction
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications :
Applications : Water Blast
PH High : 10 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$71725
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BAB751TB
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 0.75 HP
HP Standard : 0.75 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : Bronze
Elastomers : Buna-Nitrile
Voltage : 115/230 V
Phase : 1
Frequency : 50/60 Hz
Motor : TEFC
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Boiler Feed
Applications : Chemical
Applications : Condensation
Applications : Coolant
Applications : Cooling
Applications : Flooded Suction
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications :
Applications : Water Blast
PH High : 10 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$72812
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41EAB
Maximum Flow : 9 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 151.52 PSI
Head (TDH) Maximum @ 0GPM : 350 FT
TDH Minimum : 10
HP Standard : 1 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : Bronze
Elastomers : EPDM
Voltage : 230/460 V
Phase : 3
Frequency : 60 Hz
Motor : ODP
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Size : 0 "
Max. Particle Hardness : 1 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Warranty : 1 Year/s
Applications : Parts Washer
Applications : Boiler Feed
Applications : Coolant
Applications : Flooded Suction
Applications : Fuel Oil
Applications : High Pressure
Applications : Hydrostatic Test
PH High : 10 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$86457
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BAB753EB
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 0.75 HP
HP Standard : 0.75 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : Bronze
Elastomers : Buna-Nitrile
Voltage : 208-230/460 V
Phase : 3
Frequency : 50/60 Hz
Motor : EXP (C 1, Gp C/D)
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Boiler Feed
Applications : Chemical
Applications : Condensation
Applications : Coolant
Applications : Cooling
Applications : Flooded Suction
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications :
Applications : Water Blast
PH High : 10 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$106743
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BAB751EB
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 0.75 HP
HP Standard : 0.75 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : Bronze
Elastomers : Buna-Nitrile
Voltage : 115/230 V
Phase : 1
Frequency : 50/60 Hz
Motor : EXP (C 1, Gp C/D)
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Boiler Feed
Applications : Chemical
Applications : Condensation
Applications : Coolant
Applications : Cooling
Applications : Flooded Suction
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications :
Applications : Water Blast
PH High : 10 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$113022
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BSS051OV
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 1 HP
HP Standard : 0.5 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : 316SS
Elastomers : Viton
Voltage : 115/230 V
Phase : 1
Frequency : 50/60 Hz
Motor : ODP
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal : TYPE 21
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Boiler Feed
Applications : Chemical
Applications : Condensation
Applications : Coolant
Applications : Cooling
Applications : Flooded Suction
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications :
Applications : Water Blast
PH High : 12 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$148039
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BSS053OV
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 1 HP
HP Standard : 0.5 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : 316SS
Elastomers : Viton
Voltage : 208-230/460 V
Phase : 3
Frequency : 50/60 Hz
Motor : ODP
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal : TYPE 21
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Boiler Feed
Applications : Chemical
Applications : Condensation
Applications : Coolant
Applications : Cooling
Applications : Flooded Suction
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications :
Applications : Water Blast
PH High : 12 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$150817
ea.
|
Manufacturer: MTH Turbine Pump
Model Number: T41BSS753TV
Maximum Flow : 3.7 gallons/min
Minimum Flow : 1 gallons/min
TDH (Head) Maximum @ 0GPM : 259.74 PSI
Head (TDH) Maximum @ 0GPM : 600 FT
TDH Minimum : 10
HP Required : 0.75 HP
HP Standard : 0.75 HP
Inlet Connection Type : FNPT
Inlet : 1 "
Outlet Connection Type : FNPT
Outlet : 1 "
Wetted Materials : 316SS
Elastomers : Viton
Voltage : 208-230/460 V
Phase : 3
Frequency : 50/60 Hz
Motor : TEFC
Speed : 3450 RPM
Motor Frame : 56C
Length : 15 "
Self Priming : 0
Max Operating Temp : 230 °F
Viscosity : Milk 3.20 cp 40.00 ssu
Max. Particle Hardness : 5 MOH
Max. Volume of Suspended Solids : 0 %
Shaft : 304SS
Mechanical Seal : TYPE 21
Mechanical Seal Face : Carbon-ceramic
Mechanical Seal Type : Single
Impeller No. (see curve image) : B
Applications : Boiler Feed
Applications : Chemical
Applications : Condensation
Applications : Coolant
Applications : Cooling
Applications : Flooded Suction
Applications : High Pressure
Applications : Hydrostatic Test
Applications : Irrigation
Applications : Machine Tool
Applications : Parts Washer
Applications :
Applications : Water Blast
PH High : 12 pH
Efficiency : 44 %
Other : Bronze is ASTM B62.
Pumps can
| Read more… |
$156613
ea.
|
|
|
|
|
|
|
|
|
||||||